AMS2750EHeat Treatment Standard and Calibration

Update July 2020: Please note that a new F version (AMS2750F) has been released in June 2020.

In this blog post, I will take a short look attheAMS2750Estandard, with a special focus on the requirements set for calibration, calibration accuracy and test/calibration equipment.

The AMS2750E is predominantly designed forheat treatment in the aerospace industries. Heat treatment is an essential process for many critical parts of an airplane, so it is understandable that there are tight regulations and audit processes set.

While the results and success of some other industrial processes can be relatively easily measured after the process, this is not the case in a heat treatment process. Therefore, very tight control and documentation of the heat treatment process is essential to assure the quality of the end products.

AMS2750 standard

As mentioned, the AMS2750E is a standard for the heat treatment. The “AMS” name in the standard is an abbreviation of “Aerospace Materials Specifications”. The standard is published by SAE Aerospace, part of SAE International Group. The first version of the AMS2750 standard was published in1980.Followed by revisions: revision A in 1987, B also in 1987, C in 1990 and D in 2005. The current revisionAMS2750Ewas published in 2012.

The AMS2750 standard was initially developed to provide consistent specifications for heat treatment through the aerospace supply chain. The use of the standard is audited byPRI(性能Review Institute) for theNadcap(National Aerospace and Defense Contractors Accreditation Program). Prior to Nadcap, aerospace companies each audited their own suppliers, so there was a lot of redundancy and duplication of efforts. In 1990, the PRI was established to administer the Nadcap program.

AMS2750Escope

According to the standard itself, the scope of the AMS2750E standard is the following:

"This specification covers pyrometric (high temperature) requirements for thermal processing equipment used for heat treatment. It covers temperature sensors, instrumentation, thermal processing equipment, system accuracy tests, and temperature uniformity surveys. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification(s)."

为什么热处理?

In some industrial processes, it is relatively easy to measure and check the quality of the final product and judge if the product fulfills the requirements after the process is complete. You may be able to simply measure the end product and see if it is good or not.

In other processes where it is not possible/easy/practical to measure the quality of the final product you need to have a very tight control and documentation of the process conditions, in order to be sure that the final product is made according to the requirements.

It is easy to understand that heat treatment is a process where you need to have avery good control of the process in order to assure that you get the required end product, especially since the products are mostly used by the aerospace industry.

Who is it for?

The AMS2750E is predominantly designed for theaerospace industries. But the same standards and processing techniques can be used within any industry which requires control of the thermal processing of raw materials and manufactured components, such asautomotive, railandmanufacturing.

But what is the CQI-9?

The CQI-9 is a similar set of requirements for heat treatment, mainly aimed fortheautomotive industry. The first edition of CQI-9 was published in 2006.The CQI-9 “Heat Treatment System Assessment” is a self-assessment of the heat treatment system, published by AIAG (Automotive Industry Action Group). More details about CQI-9 maybe in an other post later on...

Test instruments and calibration

Let’s discussTest Instruments(calibrators) and what AMS2750E says about them.

Atraceable calibrationof different levels of measurement instruments is obviously required. The higher level standards are typically calibrated in an external calibration laboratory. The process measurements are calibrated internally using “field test instruments”.

Metrological Traceabilityis often described astraceability pyramid, or as atraceability chain,see below:

Traceability pyramid:

Traceability chain:

To learn more about themetrological traceability in calibrationread the following blog post:

Metrological Traceability in Calibration – Are you traceable?

The magical "Table 3"

In theTable 3in the AMS2750E standard, there are different specifications for the test standards and test equipment/calibrators. The different levels of instruments are classified as follows:

Reference standard
Primary standard
Secondary standard instruments
Secondary standard cell
Field test instrument
Controlling, monitoring or recording instruments

For each instrument class, there are specifications for thecalibration periodandcalibrationaccuracy. If we think about calibrators/calibration equipment, it is typically used as “field test instrument” or sometimes as “secondary standard instrument” and following are said about those:

Secondary standard instrument

Limited to laboratory calibration of field test instruments, system accuracy test sensors, temperature uniformity survey sensors, load sensors and controlling, monitoring or recording sensors

Field test instrument

Calibration of controlling, monitoring, or recordinginstrument, performanceof system accuracy tests, and temperature uniformity surveys

AMS2750Eaccuracy requirements

AMS2750Ealso specifies thecalibration periodandaccuracy requirementsfor the different levels of instruments, below is what is said about thesecondary standard instrumentandfield test instrument:

Sometimes it is easier to look at a visual, so let's look at this required calibration accuracy graphically for“field test instrument” and “secondary standard instrument”.And as the Centigrade and Fahrenheit are different, below is a graph of both for your convenience:

Contradiction with different thermocouples types and accuracy

The AMS2750E standard specifies different thermocouple types for different usage. Types B, R andS are included for more demanding use, while types J, E, K, N, T are also included in the standard.

Anyhow, the standard has thesame accuracy specification regardless of the thermocouple type. This is a slightly strange requirement, as different thermocouples have much different sensitivities.

In practice, this means that a test field instrument (calibrator) normally has a specification for millivoltage, and when this mV accuracy is converted to temperature it means that the calibrator normally hasdifferent specifications for different thermocouple types.Some thermocouple types have verylow sensitivity (voltage changes very little as temperature changes), especiallyin the lower end.

For example - a calibrator can have an electrical specification of 4 microvolts at 0 V. With a K type, this 4 µV equals a temperature of 0.1 °C (0.2 °F), but for a S type, this equals 0.7°C (1.3°F), and for a B type it equals almost 2°C (3.6 °F). Therefore, calibrators normally have very different accuracy specifications for different thermocouple types.

So the standard having the same accuracy regardless of the thermocouple type is a bit strange requirement.

To illustrate the different sensitivities of different thermocouple types, please see the graphics below. The graph shows what kind of thermovoltage (Emf) is generated in different temperature by different thermocouple types:

To learn more about thermocouples, different thermocouple types and thermocouple cold junction compensation, please read this blog post:

Thermocouple Cold (Reference) Junction Compensation

AMS2750Econtents in a nutshell

Let’s take a brief look at the contents of the AMS2750E standard and further discuss a few key points in the standard.

AMS2750E标准wi开始th sections:

1. Scope
2. Applicable documents

Chapter 3 “Technical Requirements” of AMS2570E includes the following key sections. (These sections are discussed in more details in the next chapters):

3.1 Temperature sensors
3.2.仪表
3.3. Thermal processing equipment
3.4. System Accuracy Tests (SAT)
3.5. Furnace Temperature Uniformity Survey (TUS)
3.6. Laboratory furnaces
3.7. Records
3.8. Rounding

The remaining sections are:

4. Quality assurance provisions
5. Preparation for delivery
6. Acknowledgement
7. Rejections
8. Notes

3.1 Temperature sensors

Section 3.1 discusses temperature sensors. Some key bullets from that section:

The AMS2750E standard specifies the thermocouple sensors to be used, as well as the sensor wire types.
The voltage to temperature conversion standard to be used (ASTM E 230 or other national standards).
Correction factors may be used to compensate for the errors found in calibration.
The temperature range for the sensors used.
Allowance to use wireless transmitters.
Contents of a sensor calibration certificate.
The max length of sensor wire/cable.
The max number of usage of thermocouples in different temperatures.
Types of thermocouple sensors to be used, the use for thermocouples (primary calibration, secondary calibration, sensor calibration, TUS, SAT, installation, load sensing), calibration period for thermocouples, and maximum permitted error.

3.2 Instrumentation

Section 3.2 covers the instrumentation that the sensors are used with. This includes control, monitoring, recording, calibration, instrumentation, etc.

Instruments need to be traceably calibrated.
Minimum resolution/readability of test instruments (1 °F or 1 °C).
规范电子记录。
Contents of calibration sticker:
- Date, due date, performed by, any limitations
Contents of calibration record:
- Instrument identification, make and model, standard(s) used, calibration method, required accuracy, as found and as left data of each calibration point, offset, found/left, sensitivity, statement of acceptance or rejection, any limitations or restrictions, calibration date, due date, performed by, calibration company, signature, quality, organization approval.

3.3 Thermal processing equipment

Section 3.3 discusses the furnace classification and the temperature uniformity requirements in each class. Going from class 1 having uniformity requirement of ±5°F / ±3 °C, to class 6 with ±50 °F / ±28 °C.

3.4 System accuracy test (SAT)

Section 3.4 discusses the system accuracy tests (SAT). The SAT is an on-site test where the whole measurement loop ( instrument / lead wire / sensor) is calibrated using appropriate calibration equipment. This is typically done by placing a reference thermocouple close to the thermocouple to be calibrated and comparing the read-out of the measurement loop to the reference.

SAT shall be performed with a “field test instrument,” specified in the standard’s Table 3. SAT should be performed periodically or after any maintenance. SAT interval is based on equipment class and instrumentation type.

SAT test records shall include:

identification of sensor calibrated
ID of reference sensor
ID of test instrument
date and time
set points
readings of furnace under test
test instrument readings
test sensor correction factors
corrected test instrument reading
calculated system accuracy difference
an indication of acceptance or failure
who performed the test
signature
quality organization approval

3.5 Temperature uniformity surveys (TUS)

Section 3.5 is about furnace temperature uniformity survey (TUS). The TUSis the testing of the temperature uniformity in all sections/zones of the furnace in the qualified operating range. An initial TUSneeds to be performed for any new, modified (example modifications are listed in the standard) or repaired furnace, and thereafter it should be performed in accordance with the interval specified in the standard. For furnaces with multiple qualified operating ranges, TUS shall be performed within each operating range.

There are many detailed specifications for TUStesting in the AMS2750E standard.

The TUS report shall include:

furnace identification
survey temperatures
sensor location and identification including detailed diagrams
time and temperature data from all sensors
correction factors for sensors in each temperature
as found and as left offsets
corrected/uncorrected readings of all TUS sensors at each temperature
testing company identification and signature
identification of the person who performed the survey
survey start date and time
survey end date and time
test instrumentation identification
identification of pass or fail
documentation of sensor failures (when applicable)
summary of corrected plus and minus TUS readings at each temperature after stabilization
quality organization approval

Q&A session with德意志Edelstahlwerke

We had a Questions & Answers session withMr. Julian Disse(Team Coordinator Quality Assurance Special Standards) at德意志Edelstahlwerkeand discussed on the challenges on following the AMS2750 standard, audits, measurements, calibrations, sensors, traceability and other things.

Pleasedownloadthe adjacent white paper to read the discussion.

An example customer case story

Here's an example case story of company Trescal, UK. They are a calibration service provider for aerospace customers and need to follow the AMS2750 standard. Trescal have found Beamex calibrators (MC2, MC5 andMC6) as a good fit for the work they do. Click the link below to read the case Trescal story:

情况下story: Trescal, UK - Extreme accuracy calibrations for aerospace giant

Summary

The AMS2750E specifications set a high standard for the aerospace industry. After reviewing sensor technology and the challenges for test equipment to make proper measurements, meeting accuracy requirements takes careful analysis and continuous supervision. It should be noted that the AMS2750E specifications are not easily met and accurate test equipment must be utilized. By addressing calibration requirements up front, maintenance personnel will be equipped with the proper tools and procedures to not only maintain compliance but ensure the best product quality. Good sensor measurements set the stage for good process control with repeatable results – a good formula for staying in business.

Download the free white paper

You can download the free pdf white paper by clicking the picture below:

Beamex solutions for AMS2750E

Beamex offers various temperature calibration products that can be used (and are being used) in an AMS2750E environment. You can find the detailed information of our offering on ourwebsitein the below link:

Beamex temperature calibration products

Please contact us for information on how our products can be used in an AMS2750 environment.

Please subscribe

If you like these blog articles, pleasesubscribeto this blog by entering your email address to the "Subscribe" box on the upper right-hand side. You will be notified by email when new articles are available, normally about once in month.

Also, feel free to suggest topics for new articles!